Patching a specific console signal path into an outboard recorder, 3. None of the routing screen’s tabs contains a secondary level of encoder functions. 5. These categories include: 3. Here is a brief explanation that Craig Fowler provided about the X32 routing tables used in the X32-Edit or M32-Edit (3.0 or newer). To assign various inputs to the console’s input channels, perform the following steps: 1. View and Download Behringer X32 Rack connections & overview manual online. These XLR inputs are 12kΩ, so will accept signal ranging from mic to line level. Tap the 6th encoder to toggle delay on/off. The route screen’s aux out tab allows the user to patch an internal signal path (such as a mix output used as an effects send) to the 6 separate ¼"/RCA auxiliary outputs. It was released in November 2020 and is … 5.11 Using the X32 RACK in recording and production studio environments, 5.13 Recording a 2-track directly with the console, 5.3 Recording a 2-track directly with the console. 5.5 How do I use an outboard effects processor? 5.4 How do I add one of the 8 internal effects to the sound? The routing screen’s analog out tab allows the user to patch the console’s various internal signal paths to the 8 analog XLR outputs that are located on the console rear panel. The DSP offers a total of 40 input processing channels (32 mic channels plus six aux inputs and a stereo USB input), with 25 mix buses and output channels (including 16 internal buses, six matrix outputs and three … 5.11 How do I share signals over AES50 Supermac network? 6.3 Configuring the PC to Interface with the X-USB Card, V2.0 Channel Spill Out for X32 COMPACT and PRODUCER, Gain Splitting and Remote Control for COMPACT and PRODUCER. T… Midas DL32 Digital Snake I/O Box – The Midas DL32 is a full replacement for the X32 with input/output but with the true Midas preamps. Tap the 4th encoder to assign the selected output path, completing the process. Tap the 1st encoder to connect the currently selected signal path to the AES50 pathway. Routing Screen: P16 Tab 2. (Note: Inputs and outputs on some higher-end mixers are mic and line level switchable.) AES50-B: Allows patching of internal signal paths to the 48 outputs of the rear panel AES50-B output. 5.3 How do I connect a microphone, process its signal and send it out to the P.A. Your X32 has at least two great ways for recording. A single STP CAT5e Ethernet cable can run up to 2 of the SD16’s inline before you max out the M32/X32 inputs/output. Choices include: 7. 16 Inputs (16 XLR) 8 Outputs (8 XLR) Midas DL32 Digital Snake I/O Box. 5.6 How do I set up live stage monitoring? Each of the 16 microphone inputs can accept balanced or unbalanced mic or line-level level signals and include switchable phantom power, 72 dB gain range and max +23 dBu level before clip. Feeding an external effects processor when the internal effects are insufficient, 2. You will find that there are a few different levels of line level. Local X-Y has Local 1-8, 9-16, 1-24, 25-32). The first page of the ROUTING menu is where you choose which inputs the X32 will route to the 32 input channels, (in banks of 8). TRANSFER: You may not rent, lease, lend, sell, redistribute, sublicense or provide commercial hosting services with the Software. A total of 29 programmable LCD Scribble Strips offer channel/bus identification that mirrors what is being controlled. At NAMM: Behringer Adds to X32 Line. X-Y indicates the range (eg. 8. 5.6 How do I set up live stage monitoring? Topic Guide 5.2 Default setup for connecting to monitoring and P.A. Tap the 5th encoder to complete the signal tap point assignment. 5.14 How do I set up a Matrix for a delay column/tower or a remote zone mix? 5.15 Using the X32 in recording and production studio environments, 5.17 Recording a 2-track directly with the console, 6.1 Configuring the X-USB card for use in the console, 6.2 Configuring the PC to Interface with the X-USB Card, 5.2 Default setup for connecting to monitoring and P.A. The X32 Producer has only 16 microphone inputs, but still has 32 fully featured DSP channels. 5.5 How do I use an outboard effects processor? Each of the two AES50 screens contains the same following sets of parameters that can be adjusted. By … Adjust the 1st encoder to select which of the 16 channels in the P16 bus you wish to select an audio source for. In that case you could route the S16 Stagebox to Input 1-16 (which would look the same as the below picture), and then route the physical console inputs (Local 1-16) to Channel 17-32. Tap the 5th encoder to assign the selected signal tap point. 7. The routing screen contains the following separate tabs: 1. 8. As the encoder is rotated, the currently selected input will be highlighted in the vertical list of choices. Setup and connections 1.1. Behringer X32 40-Channel, 25-Bus Digital Mixing Console provides a wealth of features in a compact design, ideal for professional live and recording applications. P16 Out: Allows patching of internal signal paths to the 16 outputs of the console’s 16-channel P16 Ultranet output. As a default, the console maps the console’s 16 rear-panel analog inputs to their the respective 16 channel inputs that are accessed on input fader layers one and two, and maps the rear panel line-level (auxiliary) inputs to the third input fader layer. X32's automated control surface is designed to present you with the control you need, when you need it. The available signal tap points include: 6. Oh, and be very careful with the latched XLR inputs on the X32 and S16s. systems 5.1 Starting up, shutting down, The X32 comes pre-configured with the local XLR inputs connected to input and firmware updates channels 1-32, and XLR outputs 1-14 connected to the mix bus masters 1-14. It appears to be equally at home on stage and in the studio, with 6 matrix mixers Repeat the above process for the other five sets of 8-channel AES50 outputs. If Behringer can shake off their historical 'cheap&nasty' stigma, this will be the product line that completely obliterates the competition at this price range, although it's doing a pretty good job already. The mixer features 32 fully programmable MIDAS-designed mic preamps. 2. Since these six outputs can have a wide variety of signal paths assigned to them, they can be used for a wide variety of tasks, such as: 1. However, the home tab of the routing screen can be used to change this default assignment and “crosspatch” different physical inputs to different channel inputs, in banks of 8 channels at a time.